About Services Tools Blog Contact us

Live Schematic and Board Editing

Inspects and edits an open circuit diagram and circuit board in KiCad, runs the electrical and design checks, and prepares manufacturing files from the same session.

  • PCB & Electronics
  • Cross-sector
  • Agent skill
  • Productised
  • Local/private
  • 2026

The problem

Board changes made by rewriting files drift away from the editor that is open, and they skip the checks a manufacturer expects. After every small change someone must rebuild the connection list, rerun the checks and prepare production files. That is where the work stalls.

What it does

A local session edits the open circuit diagram and board one step at a time, then pushes the diagram onto the board. It reports electrical rules, design rules, connections and component placement as a pass or fail list. Manufacturing export stays unavailable until that list is clear. Steps run one after another to keep the session stable.

Outcomes

  • The diagram and board stay in the open editor and do not drift from a file rewrite.
  • Rule checks run in the same session as the edit.
  • No fabrication pack is produced until the checks are clear.
  • Steps run one at a time to keep the session stable.

Simplified mockup

Interactive preview with sample data. Nothing is sent to a server.

Harbour beacon · rev C

Editors open Interface on

The live session is one step at a time. No board file is written. A parallel burst can drop the session.

Sheet 1 · power and sense
+3V3 Sheet 1 of 2 GND J1 Jack U2 3.3 V C1 100 nF U1 Beacon R1 10k D1 Harbour beacon Rev C · two layer · 3.3 V
Sheet 2 · connectors
Sheet 2 of 2 J2 Sense J3 Debug U3 Humidity SENSE
Board · 42.0 × 28.0 mm
J1 U2 U1 C1 D1

Red tracks are the front. Blue is the back. Rings mark a failed check.

Sync
Ready. Intent: 3.3 V beacon, sense header on sheet 2.
  1. Confirm both editors
  2. Read the design intent
  3. Push the schematic onto the board
Parts in the open editors
RefValueFootprintSheet
U1Beacon controllerQFN-321
U23.3 V regulatorSOT-23-51
C1100 nF04021
R110k04021
D1Green indicator06031
J1Barrel jackThrough-hole1
J2Sense header1×4 2.54 mm2
J3Debug header1×6 1.27 mm2

Rule gates

Blockers
Waiting
Export stays shut until this is zero
Session
Serial
One call, then the next
Editors
2
Schematic and board
Run
Checks have not been run this session
  1. Electrical rules
  2. Design rules
  3. Connectivity
  4. Placement
Gates
GateResult
Electrical ruleswaiting
Design ruleswaiting
Connectivitywaiting
Placementwaiting
Clear
Clear issues stays off until the check has run

Fabrication package

Withheld

Plots, the drill file, the bill of materials and the 3D model stay unavailable until the check list is clear.

Hand off
Release stays off while any gate is failing
  1. Pack plots
  2. Pack drill and the bill of materials
  3. Pack the 3D model

How it works

  1. Confirm KiCad is running with outside control enabled and the editors open.
  2. Set the project location once and read the design intent.
  3. Add or move components, wires, board parts, copper tracks and layer connections one step at a time.
  4. Push the diagram edits onto the board.
  5. Report electrical rules, design rules, connections and placement as a pass or fail list.
  6. Hold manufacturing output until the list is clear, then offer production plots, drill files, a parts list and a 3D model.

Pipeline

flowchart LR
  Open[Open project] --> Intent[Read the design intent]
  Intent --> Edit[Edit symbols or tracks]
  Edit --> Sync[Push schematic to the board]
  Sync --> Gates[Electrical and design rules]
  Gates --> Pass{Clear?}
  Pass -->|Yes| Fab[Fabrication package]
  Pass -->|No| Edit